Strength Of Material Lab Equipment

Product Price :Get Latest Price

We are engaged in providing quality approved Cantilever & Simply Supported Beam Apparatus. It consists of a well polished wooden beam one meter long resting on two knife edge end supports. This apparatus is manufactured using optimum grade raw material and sophisticated technology in synchronization with industry standards. In order to ensure quality, this apparatus is rigorously tested on various parameters by our quality controllers. Keeping in mind the diverse requirements of our clients, we provide the entire range in various sizes and specifications at affordable price.

Features:

• Excellent performance

• Reliable operation

• Less power consumption

Introduction:

• It consists of a Well Polished Wooden beam one meter long resting on two knife edge end supports.
• A central knife edge with hanger rests on the beam at the top of which a pin is provided.
• Complete with slotted weight set having two weights of 1 Kg., two weights of 500 gms. and a hanger.
• Supplied with dial gauge (Accuracy 0.01mm & Capacity 10mm) & magnetic stand.
• The whole system mounted on a MS Fabricated powder coated stand.

Approx. Rs 1.25 Lakh / SetGet Latest Price

Features:

• Industrial approved design

• High operational fluency

• Easy to operate

• AS PER IS: 5075-1969.

Introduction:

• This machine is used to test the fatigue strength of materials and to draw S-N diagram by research institute, laboratories, material manufacturers and various industries.
• This is rotating beam type machine in which load is applied in reversed bending fashion.
• The standard 8 mm dia specimen is held in special holders at its ends and located such that it experiences a uniform bending moment.
• The specimen is rotated at 4200 rpm by a motor.
• A complete cycle of reversed stresses in all fibres of the specimen is produced during each revolution.
• The bending moment is applied with the lever system and can be easily changed by moving a weight over the lever.
• Total number of revolution at which the specimen fails are recorded by a mechanical counter
• An interlocking system puts off the motor at specimen failure.
• Electronic counter instead of mechanical counter can be supplied at additional price.
• Machine with maximum bending moment up to 400 Kg. cm can be offered on request.
  

Approx. Rs 65,000 / SetGet Latest Price

Features

• Rugged construction

• Easy to use

• High performance

Introduction

• Our Pendulum Impact Tester is designed for conducting Izod and Charpy test.
• The Test methods the pendulum is mounted on antifriction bearings.
• It has two starting positions, the upper one for Charpy and the lower one for Izod testing.
• On release, the pendulum swings down to break the specimen and the energy absorbed in doing so is measured as the difference between the height of drop before rupture and the height of rise after rupture of the test specimen and is read from the position of maximum pointer on the dial scale.

General Description and Features

The machine will have following features

• Capacity 300 Joules
• Resolution 2 Joules for Charpy Test & 1 Joules for Izod Test
• Accuracy Within 0.5 %
• Release of Pendulum by Hand operation.
• Safety guards for Protection.
• Assembly to hold standard Izod and Charpy Specimens.
• Braking Arrangement provided to arrest the swing of pendulum after specimen rupture.
• Standard size specimens of Izod Impact and Charpy 2 nos for each.

Product Price :Get Latest Price

We are reckoned amongst the notorious organizations of a broad array of Universal Testing Machine. It is designed for testing metals and other materials under tension, compression bending, transverse and shear loads. The offered machine is manufactured utilizing superior quality raw material and latest technology. Moreover, a team of our quality controllers conducts a series of quality tests on the entire range to seek out any possible defect. In tune with industry standard, we provide the entire range in various customized options and industry leading prices.

Features:

• Long operational life

• Smooth functioning

• Rugged design

Universal Testing Machine:Analog/ Digital/ Computerised

Introduction:

• Universal Testing Machine is designed for testing metals and other materials under tension, compression bending, transverse and shear loads.
• Hardness test on metals can also conducted.
• Operation of the machine is by hydraulic transmission of load from the test specimen through pressure transducer to a separately house load indicator.
• The system is ideal since it replaces transmission of load through levers and knife edges, which are prone to wear and damage due to shock on rupture of test pieces.
• Load is applied by a hydrostatically lubricated ram.
• Main cylinder pressure is transmitted to the pressure transducer housed in the control panel. The transducer gives the signal to the electronic display unit corresponding to the load exerted by the main ram.
• Simultaneously the digital electronic fitted on the straining unit gives the mechanical displacement to the electronic display unit.
• Both the signals are processed by the microprocessor and load and displacement is displayed on the digital readouts simultaneously.

Electronic Control Unit :

• Microprocessor based panel incorporating state of art technology with following features.
• Front panel membrane type key board for machine operation with numeric keys for data entry.
• Data entry with numeric keyboard of test parameters including speeds, rupture % peak, preload, modulus data, test data & specimen data etc.
• 20 input data set storage, 50 results storage maintains data results during power off.
• Batch test facility for generating batch & statistic result using same data set.
• RS 232C serial port, Optional windows based software available for Online graph on PC. Data analysis, statistics, point tracing superimposing graphs to compare with standard, zooming graph etc.
• Printer port for printer interface with.
• Graph & result printout. Test certificate printout .
• Batch Certificate printout .Simple statistic printout. ,"controlled drop through guide.
• Rammer: 4.89 kg with drop of 450 mm, controlled drop through guide.
• Proving ring: high sensitivity, capacity 1000 kg with calibration chart and carrying case. Dial gauge graduated 0.0002 mm, range 5 mm.
• Strain dial gauge: least count 0.01 mm x 25 mm travel.

Approx. Rs 1.65 Lakh / SetGet Latest Price

Features:

• Excellent performance

• Precisely-designed

• Maintenance free

• AS PER IS: 18281 BS:1610.

Introduction:

• Springs are normally manufactured for a specific purpose.
• Spring reliability equals to product reliability.
• Hence, a spring manufacturer should ensure that the spring manufactured by him will meet his customer specification by testing with suitable spring testing machine.
• Most spring tests require the measurement of a load a specific height.
• This requires the testing machine to measure load and hight simultaneously to achieve the accurate and meaningful result.
• The accuracy, precis repeatability and reproducibility of test results depend on the features and performance the load testing machine.

Specifications:

• The second and fourth plates are fixed.
• The machine is capable of accommodating 20cm length 12 diameter, rod up to 100mm diameter springs for tension and 150mm length 12 springs for compression.
• Scale graduations are made up to 15cm.
• A Bourdon type Gauge is fixed for direct load measurements One fixed upright graduated to denote the deflections or tension of the springs for direct readings.
• A thimble with an arrow mark is provided to facilitate the readings.
• OPTIONAL: Digital Type Spring Testing Machine also available.

Additional Information:

• Production Capacity: 100
• Delivery Time: 2 Weeks
• Packaging Details: Wooden Crate

Approx. Rs 1.25 Lakh / SetGet Latest Price

As per the variegated requirements of our clients, we are offering a broad collection of Digital Torsion Testing Machine. This machine is manufactured using excellent quality raw material and latest technology by our skilled professionals. In order to ensure quality, this machine is stringently tested on different parameters by our experts. It is designed for conducting Torsion and Twist Tests on various metal wires, tubes, sheet materials. Apart from this, remarkable quality and sturdy structure increase the demand of our offered machine in the market.

Features:

• Less power consumption

• Highly efficient

• Compact design

Introduction:

• Torsion Testing Machine is designed for conducting Torsion and Twist Tests on various metal wires, tubes, sheet materials.
• Torque measurement is by Pendulum Dynamometer System.
• Torque ranges can be adjusted.
• Torque can be applied to specimen by geared motor through gear box.
• Autographic recorder can be provided to know the relation between torque and angle of twist on specific request.
• The Accuracy of the torque indication + 1% of the true torqu

Technical Data:

Approx. Rs 65,000 / SetGet Latest Price

• AS PER IS: 1586- 2000 for Rockwell test, IS:2281, BS:240 & ASTM-E-1 0 for Brinell test.

• The Hardness Testers have been designed and manufactured strictly conforming to IS. BS, ASTM, ISO and DIN Standards.
• Since 1966 for most exacting test requirements in the Laboratories and Workshops etc.
• These testers are designed and manufactured for measuring hardness of metals and alloys of all types, hard or soft, flat, round, tubular or irregular in shape.
• The testers are simple in design, easy to operate, yet very reliable and accurate.
• Manually operated.
• Suitable for testing hardness of metals and alloys of all kinds, hard or soft, whether flat, round or irregular shape.
• Conforms to IS:1586-2000, BS:891 (Part 1 & 2) ASTM E-18 for Rockwell test. IS: 2281- 2005, BS:240, ASTM E-10 for Brinell test.Rockwell cum Brinell hardness tester, automatic load selection with automatic zero setting dial gauge.
• Facility for brinell test with 187.5 kgf load with 2.5mm ball indentor, additional load of 250 kgf with 5mm ball indentor for testing hardness of non ferrous metal

• Loads: 60, 100, 150, 187.5, 250 kgf
• Initial load : 10 kgf Max.
• Test height : 230mm
• Depth of throat : 133mm
• Supplied complete with All Necessary accessories.

Product Price :Get Latest Price

To serve escalating requirement of our clients, we are committed towards offering a wide range of Compression Testing Machine. Our skilled professionals manufacture the entire range by using well-tested raw material and sophisticated technology. In addition to this, our offered machine is rigorously tested by our quality controllers against diverse parameters in order to deliver a defect-free range at clients'' end. Moreover, the offered machine is extensively appreciated by our clients for featuring variegated attributes like precise design and sturdiness.

Features:

• High efficiency

• Trouble-free operation

• Low maintenance

• AS PER IS: IS-516, B.S.S,1610,1881

• PILLAR TYPE LOAD FRAME: There are two/ Four pillar type of load frames. Two solid pillars are vertically fixed to a sturdy base and at other end is fixed across-head. The height of the cross head is also slightly adjustable. A lead screw passes through the center of cross-head. To the lower end of this lead screw is fixed upper platen with a spherical seat for self alignment. At the center of the base plate is fixed a jack, on the top of which the lower platen with the help of a centering pin is kept. The distance between the upper end platen is variable by means of the lead screw. A spacer block is also supplied with the load frame. This spacer block which can be fitted on the top of the jack and below the lower platen by means of centering pins helps reduce the distance between the two platens. The platens are well machined, polished and hardened. The lower platen has concentric grooves to centrally place the specimen.

• ELECTRICALLY CUM HAND OPERATED PUMPING UNIT: This is a separate console housing an oil tank, electric motor, relay etc. A drain Plug to remove oil is fitted at the base of the tank. The pumping unit has on its front panel a slow-fast lever to control the rate of loading, a release valve and a slit to enable a rod to be inserted in the hand pump to operate the pumping unit manually. A pressure gauge is fitted in front at a convenient angle. The pumping unit works on 230 V A.C. or 415 V, 3 8 supply. This pumping unit is connected to the load frame by means of pressure pipes.

Note:

• Digital versions of electrically operated Compression Testing Machines can also be supplied. The digital versions have 0.5% accuracy